Frigidaire Dishwasher FGID2466QF4A Operation Manual

The Frigidaire Gallery FGID2466QF4A is a 24-inch built-in stainless steel dishwasher designed for quiet, energy-efficient, and powerful cleaning. Featuring advanced DishSense® Technology, OrbitClean® spray arms, and an NSF®-Certified Sanitize Option, it automatically adjusts the wash cycle to the soil level for optimal results. This ENERGY STAR® certified appliance combines efficiency with modern design, suitable for most residential kitchen installations.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Dishwasher 2.3. Care and Cleaning 2.4. Troubleshooting 3. Installation Instructions 3.1. Remove Old Dishwasher 3.2. Installing New Dishwasher 3.3. Electrical Connections 3.4. Water Supply 3.5. Drain Connection

Key Specifications

Model: FGID2466QF4A (Frigidaire Gallery Series)
Type: 24-inch built-in dishwasher with stainless steel finish
Electrical Requirements:
- 120 V, 60 Hz, 15A dedicated circuit
- 3-wire with ground connection
Dimensions: 24" W x 25" D x 33-1/2" – 34-1/2" H (adjustable leveling)
Water Requirements:
- Water pressure: 20–120 PSI
- Hot water supply: minimum 120°F (49°C)
Capacity: Up to 14 place settings
Noise Level: 54 dBA (quiet operation)
Wash Cycles:
- Power Plus (Heavy)
- Normal Wash
- Top Rack Only
- Energy Saver
- Favorite (Custom cycle)
Options:
- Heat Dry / Air Dry
- Hi-Temp Wash
- Sanitize (NSF® Certified)
- Delay Start (1–24 hrs)
- Control Lock
Special Features:
- DishSense® Technology for automatic cycle adjustment
- OrbitClean® spray arm for complete coverage
- Stay-Put Door design
- Smudge-Proof™ stainless steel exterior

Operation Instructions

Initial Setup

1. Load Dishes: Remove large food debris; load dishes according to rack guide. Sharp utensils should face downward.
2. Add Detergent: Fill the dispenser with fresh dishwasher detergent suitable for automatic machines.
3. Add Rinse Aid: Check indicator and fill as needed to improve drying performance.
4. Run Hot Water: Let water run at the sink until hot before starting the cycle.
5. Check Filters and Arms: Ensure spray arms rotate freely and filters are clean.
6. First Use: Run an empty Normal cycle with detergent to clean the system.

Operating the Dishwasher

1. Select Cycle: Choose among Power Plus, Normal, Energy Saver, or Top Rack.
2. Select Options: Add features such as Hi-Temp Wash or Sanitize.
3. Delay Start: Press to delay operation up to 24 hours.
4. Start: Close the door firmly and press Start. Cycle begins automatically.
5. Pause/Resume: Open door to pause, close to resume.
6. Cancel: Hold Start for 3 seconds to cancel and drain.
Note: Steam release during drying is normal. Dishes may be hot after sanitize mode.

Care and Cleaning

1. Filters: Rinse the bottom filter under warm water monthly.
2. Spray Arms: Remove and clean holes to prevent blockages.
3. Interior: Wipe stainless surfaces with mild detergent; avoid abrasives.
4. Vinegar Clean: Place 2 cups of white vinegar in the lower rack and run a Normal cycle monthly.
5. Exterior: Use soft cloth with stainless cleaner; avoid harsh chemicals.
Tip: Keep rinse aid filled for spotless, streak-free drying.

Troubleshooting

Dishwasher won’t start: Check breaker, latch, and power connection.
Water not draining: Inspect hose, air gap, and filter for clogs.
Poor cleaning results: Ensure water is hot enough and spray arms are not blocked.
White film on dishes: Add rinse aid or adjust detergent for hard water.
Dishwasher leaking: Verify leveling and door seal condition.
Display shows “UO” or “i20”: Indicates vent or drain error; contact service.
Noise: Light humming or water movement is normal operation.

Installation Instructions

Warning: Turn off electrical and water supply before installation. Follow all local plumbing and electrical codes.

Remove Old Dishwasher

Disconnect power at breaker and shut off water supply.
Detach drain hose, water line, and electrical wiring.
Remove mounting screws and slide the old unit out carefully.
Cap electrical and water lines temporarily to prevent leaks.

Installing New Dishwasher

Prepare Opening: Standard 24" wide space required.
Adjust Leveling Legs: Align height to countertop.
Connect Drain Hose: Route through cabinet hole to sink or disposer.
Slide Unit: Move dishwasher carefully into position.
Secure: Attach to countertop using provided brackets.
Connect Water Supply and Electrical: See below subsections.
Test Run: Check for leaks and perform a short wash cycle.

Electrical Connections

120V/15A dedicated grounded circuit required.
Connect black (hot), white (neutral), and green (ground).
Use junction box and strain relief for safety.
No extension cords permitted.

Water Supply

Use 3/8" copper or braided stainless steel tubing.
Flush line before connection to prevent debris blockage.
Connect using compression fitting; avoid sharp bends.
Ensure water temperature ≥ 120°F (49°C).

Drain Connection

Connect to sink drain or disposer using high loop or air gap.
Secure hose with clamp; avoid kinks or sags.
Maintain minimum height of 32" from floor for loop.
Inspect for leaks after installation.