Frigidaire FFCD2413UW Dishwasher Operation Manual

The Frigidaire FFCD2413UW is a 24-inch built-in dishwasher in white finish, featuring DishSense Technology for cycle adjustment based on load, and quieter operation. It fits up to 14 place settings with filtered wash system for efficient cleaning. Below are the key specifications and operation instructions.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Dishwasher 2.3. Care and Cleaning 2.4. Troubleshooting 3. Installation Instructions 3.1. Remove Old Dishwasher 3.2. Installing New Dishwasher 3.3. Electrical Connections 3.4. Water Supply 3.5. Drain Connection

Key Specifications

Type: 24-inch built-in dishwasher with DishSense Technology
Compatibility:
- Residential use; standard household plumbing and electrical
- Hot water supply recommended
- Not for items not marked dishwasher safe
Power Source:
- 120 V, 60 Hz household current
- Dedicated circuit recommended
Electrical Rating:
- Standard 15A circuit breaker
Dimensions: Standard 24" width; exact height/depth per installation (leveling required)
Features:
- Wash cycles: Normal Wash
- Options: High Temp Wash, HEAT DRY, Control Lock
- Capacity: Up to 14 place settings
- Upper and lower racks, silverware basket, rinse aid and detergent dispensers
- Continuously filtered wash, glass trap for debris
- Quieter operation than typical dishwashers
Operating Conditions:
- Hot water supply for best performance
- Protect from freezing in unheated areas
Wash Cycle Details:
- Normal: Variable time based on load, with options

Operation Instructions

Initial Setup

1. Read Safety Info: Review all warnings before use.
2. Level Unit: Ensure dishwasher is level.
3. Add Rinse Aid: Fill dispenser and adjust level 1-6 for spotting prevention.
4. Prepare Load: Scrape food, loosen burned-on soils, empty liquids from items.
5. First Use: Run hot water at faucet until hot, then select cycle.

Operating the Dishwasher

1. Load Dishes: Follow patterns for place settings; face items toward spray arms; avoid nesting.
2. Add Detergent: Use main cup for normal loads, pre-wash for heavy; close cover.
3. Select Cycle/Options: Choose Normal Wash, add High Temp Wash and HEAT DRY for best results.
4. Start: Close door to latch; press START/CANCEL; cycle begins automatically.
5. Control Lock: Hold Options for 3 seconds to lock/unlock.
6. Interrupt: Open door to pause; close to resume.
Note: Cycle times vary; normal sounds include water spray and draining.

Care and Cleaning

1. Interior: Allow heating element to cool; clean with mild detergent.
2. Filters/Glass Trap: Remove, rinse debris, reinstall monthly.
3. Spray Arms: Remove and clean holes as needed.
4. Exterior: Wipe with soft cloth and mild soap.
5. Monthly: Clean inlet valve screen.
Note: Winterize by draining lines if unused.

Troubleshooting

Won't Start: Check door latch, controls unlocked, power on, no delay.
Won't Fill: Verify water supply, clean inlet screen, check overfill protector.
Poor Drying: Use HEAT DRY and rinse aid; ensure hot water.
Chipped Dishes: Load carefully; use top rack for delicates.
Odor: Run cycles regularly; clean filters.
Leaks: Level unit; check seal and detergent amount.
Noisy: Normal operation; secure loose items.
Note: Contact support if issues persist: 1-800-374-4432 (USA).

Installation Instructions

Warning: Disconnect power and water before installation; professional recommended if needed.

Remove Old Dishwasher

Disconnect power at breaker, water supply, and drain hose.
Unfasten from cabinet/counter; slide out carefully.
Cap lines to prevent drips.

Installing New Dishwasher

Prepare Cabinet: Ensure proper opening and access to utilities.
Level: Adjust legs for even stance to prevent leaks/odors.
Route Lines: Position water, drain, and electrical.
Slide In: Align and secure to countertop/cabinet.
Connect All: See subsections; test for leaks.
Final Check: Run cycle to verify operation.

Electrical Connections

120V/60Hz dedicated circuit; ground properly.
Disconnect at source before work.
No extension cords.

Water Supply

Connect to hot water line; clean inlet screen.
Turn on supply; flush before first use.
Drain for winterizing.

Drain Connection

Secure to sink/disposer without kinks.
Ensure high loop or air gap per code.
Drain sump for storage.