Frigidaire FFCD2418US Dishwasher Operation Manual

The Frigidaire FFCD2418US is a 24-inch built-in dishwasher with stainless steel finish, featuring Precision Direct Wash System for efficient cleaning and quieter operation. It supports 10-12 place settings capacity, NSF certified for residential use, and operates on standard 120V household current. Ideal for modern kitchens, it's compatible with standard plumbing and electrical systems. Below are the key specifications and operation instructions.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Dishwasher 2.3. Care and Cleaning 2.4. Troubleshooting 3. Installation Instructions 3.1. Remove Old Dishwasher 3.2. Installing New Dishwasher 3.3. Electrical Connections 3.4. Water Supply 3.5. Drain Connection

Key Specifications

Type: 24-inch built-in dishwasher with Precision Direct Wash System
Compatibility:
- Residential use; NSF certified
- Standard 120V, 60Hz household current
- Water pressure: 20-120 PSI
- Hot water supply at least 120°F (49°C)
- Compatible with food waste disposers (if empty)
Power Source:
- 120 V, 60 Hz; 15A circuit (20A if connected to disposer)
- Grounded outlet required
Electrical Rating:
- 15A fuse or circuit breaker
- 2-wire with ground
Dimensions: Standard 24" width; exact height/depth per installation guide
Features:
- Wash cycles: Heavy, Normal, 1 Hr Wash, Energy Saver, Rinse Only
- Options: Sanitize, Hi-Temp Wash, Heat Dry, Delay Start (4 hours)
- Capacity: 10-12 place settings; adjustable racks with fold-down shelves
- Detergent and rinse aid dispensers; glass trap filter
- Quiet operation with energy-efficient motors
Operating Conditions:
- Water temperature: Minimum 120°F (49°C)
- Humidity: Non-condensing
Wash Cycle Details:
- Heavy: ~2-3 hrs, ~9 gal
- Normal: ~1.25-3 hrs, ~3.2-7 gal
- 1 Hr Wash: ~1-2.25 hrs, ~4.3 gal
- Energy Saver: ~1 hr, ~4.5 gal
- Rinse Only: ~17 min, ~2.3 gal

Operation Instructions

Initial Setup

1. Load Dishes: Scrape large food particles; load racks properly for 10-12 place settings, avoiding nesting; place sharp items handles up.
2. Add Detergent: Use automatic dispenser; amount based on soil level and water hardness.
3. Add Rinse Aid: Fill dispenser as needed.
4. Run Hot Water: At sink until hot (120°F+), then close.
5. Select Cycle: Use control panel; lights confirm.
6. First Use: Run empty Normal cycle with detergent.

Operating the Dishwasher

1. Select Cycle: Press for Heavy, Normal, 1 Hr Wash, Energy Saver, or Rinse Only.
2. Select Options: Sanitize (NSF certified), Hi-Temp Wash, Heat Dry, Delay Start.
3. Control Lock: Hold OPTIONS for 3 seconds to lock.
4. Start: Close door firmly; press START/CANCEL. Unit fills, washes, rinses, dries.
5. Interrupt Cycle: Open door (pauses); add items within 10 minutes, close to resume.
6. Cancel: Hold START/CANCEL for 3 seconds to drain and reset.
Note: Unit remembers last cycle; normal sounds include sprays and drains.

Care and Cleaning

1. Filter: Self-cleaning; empty glass trap periodically by removing and rinsing.
2. Spray Arms: Ensure free rotation; clear clogs if needed.
3. Exterior/Interior: Wipe with mild soap; avoid abrasives.
4. Monthly Clean: 2 cups white vinegar in bottom, run Normal (no detergent) for spots/film.
5. Rinse Aid: Refill as needed.
Note: Clean overfill protector; winterize in cold areas by draining lines.

Troubleshooting

Won't Start: Check power, door latch, cycle selected, no Delay Start.
No Water Fill: Water supply on? Pressure 20+ PSI; run hot water first.
Poor Drainage: Hose kinked? Disposer empty? Clean glass trap.
Soils on Dishes: Use longer cycle; pre-rinse heavy soils; hot water.
Spotting/Filming: Check water hardness; increase rinse aid; vinegar clean.
Not Drying: Select Heat Dry; use rinse aid; towel dry plastics.
Leaking: Level unit; check door gasket; correct detergent.
Long Cycles: Normal with options; sensor adjusts.
Note: If issues persist, contact Frigidaire support.

Installation Instructions

Warning: Disconnect power and water before installation. Follow local codes; improper setup may void warranty. Use qualified technician for electrical.

Remove Old Dishwasher

Shut off power at breaker and water supply.
Disconnect drain hose, water line, electrical.
Unfasten from cabinet/counter; slide out.
Cap lines to prevent drips.

Installing New Dishwasher

Cabinet Prep: Ensure opening for 24" unit; utilities access.
Level Legs: Adjust to fit under counter.
Route Hoses/Wires: Through cabinet hole.
Slide In: Align, push fully; connect drain first.
Level: Front-to-back and side-to-side.
Secure: Screws to countertop/cabinet.
Connect Water/Drain/Electrical: See subsections.
Test: Check for leaks; run cycle.

Electrical Connections

120V/15A dedicated circuit (20A with disposer); no extension cords.
Connect black to hot, white to neutral, green to ground.
Use junction box or cord (3-prong).
Secure with strain relief; ground electrically.

Water Supply

Connect to hot water line; shut-off valve.
Flush line; 20-120 PSI; minimum 120°F.
Avoid kinks.

Drain Connection

High loop or air gap (clean periodically).
Connect to sink/disposer (remove plug if needed).
Secure clamps; no kinks or sags.
Empty disposer before use.