Frigidaire FGIP2468UF Dishwasher Operation Manual

The Frigidaire FGIP2468UF is a 24-inch built-in dishwasher with stainless steel finish, featuring Dual OrbitClean® Wash System for superior cleaning and SaharaDry™ drying technology. It offers 14 place settings capacity, ENERGY STAR® certification, and quiet 49 dBA operation. Ideal for modern kitchens, it's compatible with standard plumbing and electrical systems. Below are the key specifications and operation instructions.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Dishwasher 2.3. Care and Cleaning 2.4. Troubleshooting 3. Installation Instructions 3.1. Remove Old Dishwasher 3.2. Installing New Dishwasher 3.3. Electrical Connections 3.4. Water Supply 3.5. Drain Connection

Key Specifications

Type: 24-inch built-in dishwasher with Dual OrbitClean® Wash System and SaharaDry™ drying
Compatibility:
- Residential use; ENERGY STAR® and NSF certified
- Standard 120V, 60Hz household current
- Water pressure: 20-120 PSI
- Hot water supply at least 120°F (49°C)
- Compatible with food waste disposers (if empty)
Power Source:
- 120 V, 60 Hz; 15A circuit (dedicated, max 20A with disposer)
- Grounded outlet required
Electrical Rating:
- 15A fuse or circuit breaker
- 2-wire with ground
Dimensions: 24" W x 25" D x 33-1/2" - 35" H (adjustable)
Features:
- Wash cycles: PowerPlus™ (Heavy), Normal, Quick Wash (34 min), Favorite, China Crystal, Rinse Only, Energy Saver Plus, Top Rack Only
- Options: MaxBoost™ Dry, Heat/No Heat Dry, Wash Pressure, Hi-Temp Wash, Sanitize (NSF certified), Delay Start (1-24 hours)
- Capacity: 14 place settings; adjustable racks with fold-down tines
- Dual OrbitClean® for better coverage; DishSense® Technology adjusts cycle time; AquaSurge™ adjustable pressure
- Stainless steel tub and filter; low rinse-aid indicator; Smudge-Proof™ finish
- Quiet: 49 dBA; Annual Energy: 268 kWh
Operating Conditions:
- Water temperature: 120°F min (49°C)
- Humidity: Non-condensing
Wash Cycle Details:
- Normal: ~1-2 hrs, 4.9-8.5 gal
- Heavy: ~2.5 hrs, ~8 gal
- Quick: ~34 min, ~4 gal
- Rinse Only: ~30 min, ~2 gal

Operation Instructions

Initial Setup

1. Load Dishes: Scrape large food particles; load upper/lower racks and silverware basket properly, avoiding nesting.
2. Add Detergent: Use automatic dispenser; fresh powder, liquid, or gel based on soil level.
3. Add Rinse Aid: Fill dispenser (indicator light when low); adjust for spotting.
4. Run Hot Water: At sink until hot, then close.
5. Select Cycle: Use Express-Select® controls; lights confirm.
6. First Use: Run empty Normal cycle with detergent.

Operating the Dishwasher

1. Select Cycle: Press for PowerPlus™, Normal, Quick Wash, etc.
2. Select Options: MaxBoost™ Dry, Hi-Temp Wash, Sanitize, Delay Start.
3. Control Lock: Hold for 3 seconds to lock controls.
4. Start: Close door firmly; press Start. Unit fills, washes, rinses, dries.
5. Interrupt Cycle: Open door (pauses); add items, close to resume.
6. Cancel: Hold Start for 3 seconds to drain and reset.
Note: DishSense® may shorten cycles; normal sounds include sprays and drains. To start with door open: Select cycle, press Start, then close door.

Care and Cleaning

1. Filter: Self-cleaning; empty glass trap monthly: Rotate handle, lift assembly, empty, rinse, replace.
2. Spray Arms: Check for clogs; clear with toothpick.
3. Exterior/Interior: Wipe with soft cloth and mild soap; avoid abrasives.
4. Monthly Clean: 2 cups white vinegar in bottom rack, run Normal (no detergent).
5. Rinse Aid: Refill as needed; adjust dispenser setting.
Note: Clean overfill protector; use dishwasher-safe items only.

Troubleshooting

Won't Start: Check power, door latch, cycle selected, no Delay Start; ensure water supply on.
No Water Fill: Verify pressure 20+ PSI, clean inlet screen, hot water.
Poor Drainage: Hose kinked? Disposer empty? Clean filter and air gap.
Soils on Dishes: Pre-rinse heavy soils; use correct cycle/detergent; check loading.
Spotting/Filming: Hard water? Increase rinse aid; vinegar clean.
Not Drying: Select MaxBoost™ Dry; unload promptly.
Leaking: Level unit; check door seal; correct detergent amount.
Error Codes (e.g., Er, Uo): Reset power; clean filters; if persists, contact support at 1-800-944-9044.
Note: For odors, clean drain and interior.

Installation Instructions

Warning: Disconnect power and water before installation. Follow local codes; improper setup may void warranty.

Remove Old Dishwasher

Shut off power at breaker and water supply.
Disconnect drain hose, water line, electrical.
Unfasten from cabinet/counter; slide out.
Cap lines to prevent drips.

Installing New Dishwasher

Cabinet Prep: 24" W x 24" D x 34-1/4" - 35-3/4" H opening; utilities access.
Level Legs: Adjust to fit under counter.
Door Springs: Adjust for balance.
Route Hoses/Wires: Through cabinet hole (left/right bottom front).
Slide In: Align, push fully; connect drain first.
Level: Front-to-back and side-to-side; 2" clearance for door.
Secure: Screws to countertop/cabinet.
Connect Water/Drain/Electrical: See subsections.
Test: Check for leaks; run cycle.

Electrical Connections

120V/15A dedicated circuit; no extension cords.
Connect black to hot, white to neutral, green to ground.
Use junction box or cord (3-prong).
Secure with strain relief.

Water Supply

3/8" NPT copper tubing; shut-off valve.
Flush line; connect to inlet with ferrule/nut.
20-120 PSI; 120°F min temp.
Avoid kinks.

Drain Connection

High loop or air gap (required by code).
Connect to sink/disposer (remove plug).
Secure clamps; max length 10 ft, min height 32".
No sags in hose.