Frigidaire LFBD2409LF Dishwasher Operation Manual

The Frigidaire LFBD2409LF is a 24-inch built-in dishwasher featuring a stainless steel tub, multiple wash cycles, and ENERGY STAR certification for efficient cleaning. It accommodates up to 14 place settings and includes options like High Temp Wash and Heat Dry. Below are the key specifications and operation instructions.

Key Specifications

• Type: 24-inch built-in dishwasher with stainless steel tub
• Compatibility:
  • Residential use; ENERGY STAR certified
  • Standard 120V, 60Hz household current
  • Water pressure: 20-120 PSI
  • Hot water supply at least 120°F (49°C)
  • Compatible with food waste disposers
• Power Source:
  • 120 V, 60 Hz; 15A circuit
  • Individual grounded branch circuit
• Electrical Rating:
  • 15A fuse or circuit breaker
  • 2-wire with ground
• Dimensions: 24" W x 24" D x 33-1/2" - 34-1/2" H (adjustable)
• Features:
  • Wash cycles: Normal, Heavy, Light, Rinse Only
  • Options: Heat Dry, Hi-Temp Wash, Control Lock
  • Capacity: 14 place settings
  • Self-cleaning filter, rinse aid dispenser
  • Quiet operation: 55 dBA
• Operating Conditions:
  • Water temperature: 120°F-150°F
  • Humidity: 90% non-condensing
• Wash Cycle Details:
  • Normal: ~1.8 hrs, 4.5 gal
  • Heavy: ~2.5 hrs, 7.2 gal
  • Light: ~1 hr, 3.5 gal
  • Rinse Only: ~20 min, 2 gal

Operation Instructions

Initial Setup

1. Load Dishes: Scrape food; load racks without nesting.
2. Add Detergent: Use fresh detergent in dispenser.
3. Add Rinse Aid: Fill dispenser; adjust for spotting.
4. Hot Water: Run faucet until hot.
5. Select Cycle: Press buttons; lights indicate.
6. Start: Close door; press Start.

Operating the Dishwasher

1. Select Cycle: Normal for daily, Heavy for pots.
2. Options: Hi-Temp for sanitizing, Heat Dry.
3. Lock: Hold for 3 sec.
4. Start: Latch door; press Start.
5. Pause: Open door; close to resume.
6. Cancel: Hold Start 3 sec to drain.
Note: Times vary with load.

Care and Cleaning

1. Filter: Clean monthly; remove and rinse.
2. Spray Arms: Clear clogs.
3. Exterior: Mild soap.
4. Interior: Vinegar cycle monthly.
5. Rinse Aid: Refill as needed.
Note: Use safe items only.

Troubleshooting

• No Start: Check power, door, lock.
  
• No Fill: Water on? Clean screen.
  
• No Drain: Kink? Clean filter.
  
• Poor Clean: Hot water, detergent.
  
• Spots: Rinse aid, hardness test.
  
• Leak: Level, seal.
  Note: Call support if needed.

Installation Instructions

Warning: Disconnect power/water; follow codes.

Remove Old Dishwasher

• Off power/water.
  
• Disconnect lines.
  
• Remove from cabinet.

Installing New Dishwasher

1. Prep cabinet.
   
2. Level legs.
   
3. Route lines.
   
4. Slide in, secure.
   
5. Connect all.
   
6. Test.

Electrical Connections

• 120V/15A ground.
  
• Wire nuts.
  
• Strain relief.

Water Supply

• 3/8" copper, valve.
  
• Flush, connect.
  
• Check leaks.

Drain Connection

• Air gap/high loop.
  
• Clamp secure.
  
• No sags.