Frigidaire LGID2475QF3A Dishwasher Operation Manual

The Frigidaire LGID2475QF3A is a 24-inch built-in dishwasher with stainless steel finish, featuring DishSense® Technology to automatically adjust cycles based on soil levels. It offers up to 14 place settings capacity, ENERGY STAR® certification, and quiet operation. Ideal for modern kitchens, it's compatible with standard plumbing and electrical systems. Below are the key specifications and operation instructions.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Dishwasher 2.3. Care and Cleaning 2.4. Troubleshooting 3. Installation Instructions 3.1. Remove Old Dishwasher 3.2. Installing New Dishwasher 3.3. Electrical Connections 3.4. Water Supply 3.5. Drain Connection

Key Specifications

Type: 24-inch built-in dishwasher with DishSense® Technology
Compatibility:
- Residential use; ENERGY STAR® certified
- Standard 120V, 60Hz household current
- Water pressure: 20-120 PSI
- Hot water supply at least 120°F (49°C)
- Compatible with food waste disposers (if empty)
Power Source:
- 120 V, 60 Hz; 15A circuit (20A if with disposer)
- Grounded outlet required
Electrical Rating:
- 15A fuse or circuit breaker
- 2-wire with ground
Dimensions: 24" W x 25" D x 33-1/2" - 35" H (adjustable)
Features:
- Wash cycles: Heavy, Normal, Quick Wash, Rinse Only
- Options: Heat Dry, Hi-Temp Wash, Sanitize (NSF certified), Delay Start
- Capacity: 14 place settings
- DishSense® Technology adjusts cycle; adjustable racks with fold-down tines
- Stainless steel tub; rinse aid dispenser
- Quiet operation; Annual Energy: ENERGY STAR certified
Operating Conditions:
- Water temperature: 120°F min (49°C)
- Humidity: Non-condensing
Wash Cycle Details:
- Normal: ~2 hrs, ~5 gal
- Heavy: ~2.5 hrs, ~7 gal
- Quick Wash: ~1 hr, ~4 gal
- Rinse Only: ~30 min, ~2 gal

Operation Instructions

Initial Setup

1. Load Dishes: Scrape large food particles; load upper/lower racks and silverware basket properly, avoiding nesting; place sharp items handles up.
2. Add Detergent: Use automatic dispenser; fresh powder, liquid, or gel based on soil level and water hardness.
3. Add Rinse Aid: Fill dispenser (light indicates low); adjust for drying performance.
4. Run Hot Water: At sink until hot (120°F+), then close faucet.
5. Select Cycle: Use control panel; confirm with lights.
6. First Use: Run empty Normal cycle with detergent.

Operating the Dishwasher

1. Select Cycle: Press for Heavy, Normal, Quick Wash, or Rinse Only.
2. Select Options: Heat Dry, Hi-Temp Wash, Sanitize, Delay Start.
3. Control Lock: Hold START/CANCEL for 3 seconds to lock.
4. Start: Close door firmly; press START/CANCEL. Unit fills, washes, rinses, dries.
5. Interrupt Cycle: Open door (pauses); add items within 10 minutes, close to resume.
6. Cancel: Hold START/CANCEL for 3 seconds to drain and reset.
Note: DishSense® adjusts cycle time; normal sounds include splashing and motors. Contents hot after Sanitize.

Care and Cleaning

1. Filter: Self-cleaning; clean glass trap monthly: remove, rinse under water.
2. Spray Arms: Check and clear clogs monthly with toothpick.
3. Exterior/Interior: Wipe with soft cloth and mild soap; avoid abrasives.
4. Monthly Clean: 2 cups white vinegar in bottom rack, run Normal (no detergent).
5. Rinse Aid: Refill as needed; adjust dispenser setting.
Note: Use dishwasher-safe items only; clean overfill protector.

Troubleshooting

Won't Start: Check power, door latch, cycle selected, no Delay Start.
No Water Fill: Water supply on? Clean inlet screen; pressure 20+ PSI.
Poor Drainage: Hose kinked? Disposer empty? Clean filter.
Soils on Dishes: Pre-rinse heavy soils; use correct cycle/detergent; hot water.
Spotting/Filming: Increase rinse aid; test water hardness; vinegar clean.
Not Drying: Select Heat Dry; unload promptly.
Leaking: Level unit; check door seal; correct detergent amount.
Long Cycles: Normal with options; DishSense® adjusts.
Note: If issues persist, contact Frigidaire at 1-800-374-4432.

Installation Instructions

Warning: Disconnect power and water before installation. Follow local codes; improper setup may void warranty. Use qualified technician for electrical.

Remove Old Dishwasher

Shut off power at breaker and water supply.
Disconnect drain hose, water line, electrical.
Unfasten from cabinet/counter; slide out.
Cap lines to prevent drips.

Installing New Dishwasher

Cabinet Prep: 24" W x 24" D opening; utilities access.
Level Legs: Adjust to fit under counter (33-1/2" min height).
Door Springs: Adjust for balance.
Route Hoses/Wires: Through cabinet hole.
Slide In: Align, push fully; connect drain first.
Level: Front-to-back and side-to-side.
Secure: Screws to countertop/cabinet.
Connect Water/Drain/Electrical: See subsections.
Test: Check for leaks; run cycle.

Electrical Connections

120V/15A dedicated circuit (20A with disposer); no extension cords.
Connect black to hot, white to neutral, green to ground.
Use junction box or cord (3-prong).
Secure with strain relief.

Water Supply

3/8" NPT copper tubing; shut-off valve.
Flush line; connect to inlet with ferrule/nut.
20-120 PSI; 120°F min temp.
Avoid kinks.

Drain Connection

High loop or air gap (required by code).
Connect to sink/disposer (remove plug).
Secure clamps; max length 10 ft, min height 32".
No sags in hose.