Frigidaire Refrigerator FGHD2368TF Operation Manual

The Frigidaire FGHD2368TF is a 21.7 cu ft counter-depth French door refrigerator from the Gallery series. It combines advanced storage flexibility, filtered water & ice dispenser, LED lighting, and energy-efficient design to keep food fresh and well organized. This manual provides specifications, operation instructions, care & maintenance, troubleshooting tips, and installation guidance for safe and effective use.

Key Specifications

• Model: FGHD2368TF (Gallery French Door Counter-Depth) :contentReference[oaicite:1]{index=1}
• Type: Counter-Depth French Door Refrigerator with bottom freezer :contentReference[oaicite:2]{index=2}
• Capacity: ~21.7 cu ft total :contentReference[oaicite:3]{index=3}
• Dimensions:
  • Height (with hinges & rollers): ~ 69-7/8″ (≈ 1775 mm) :contentReference[oaicite:4]{index=4}
  • Width (doors): 36″ (≈ 914 mm) :contentReference[oaicite:5]{index=5}
  • Depth (including door): ~ 28-½″ (≈ 724 mm) :contentReference[oaicite:6]{index=6}
• Certifications & Features:
  • ENERGY STAR® certified :contentReference[oaicite:7]{index=7}
  • Star-K / Sabbath mode supported :contentReference[oaicite:8]{index=8}
  • PureSource Ultra® II water & ice filter :contentReference[oaicite:9]{index=9}
  • PureAir Ultra® II air filtration :contentReference[oaicite:10]{index=10}
  • EvenTemp™ technology for consistent cooling :contentReference[oaicite:11]{index=11}
  • Store-More™ shelves, flip-up, full-width Cool Zone™ drawer, multi-level LED lighting :contentReference[oaicite:12]{index=12}

Operation Instructions

Initial Setup

1. Remove all packaging material, tape, foam, and staples from inside and outside the refrigerator.
2. Clean interior surfaces with mild soap and warm water, then dry thoroughly.
3. Position the refrigerator in its site—leave space for ventilation and door swing.
4. Level the unit (see Installation section).
5. Connect power and water (for models with ice/water).
6. Allow the refrigerator to run empty for at least 4 hours (or as recommended) before loading food.

Controls & Settings

Use the control panel (usually inside or on the front door) to set temperatures and options. Typical controls include:

• Refrigerator / Freezer Temperature: adjust settings to cool or warm.
  Let settings stabilize for 24 hours before further adjustment.
• Sabbath / Sabbath Mode: activates features to comply with observance days. :contentReference[oaicite:13]{index=13}
• Ice & Water Dispenser: toggle water / crushed / cubed ice modes.
  Some models include lock, light, and filter change indicator functions. :contentReference[oaicite:14]{index=14}
• Alerts & Alarms: door ajar, temperature alerts, filter change reminders, power failure alerts. :contentReference[oaicite:15]{index=15}

Using the Dispenser & Ice Maker

• Connect water supply properly before using.
  Make sure the line is flushed to remove debris. :contentReference[oaicite:16]{index=16}
• Use only authorized water filter cartridges (e.g. PureSource Ultra II) to ensure safe water & ice quality. :contentReference[oaicite:17]{index=17}
• Allow time after installation for water to flow and ice to form (often 24–48 hrs).
  Discard first few batches of ice. :contentReference[oaicite:18]{index=18}
• When selecting ice type (crushed / cubed), allow water to purge prior to first use.
  Lock / unlock dispenser functions using control panel. :contentReference[oaicite:19]{index=19}

Storage & Shelving

• Use adjustable shelves and flip-up sections to accommodate tall items. :contentReference[oaicite:20]{index=20}
• Store produce in humidity-controlled crispers.
  Use the Cool Zone™ drawer for deli or meats. :contentReference[oaicite:21]{index=21}
• Keep door bins for bottles, condiments, and smaller items.
  Avoid overloading door bins. :contentReference[oaicite:22]{index=22}
• Do not block air vents inside; ensure air circulation for consistent cooling.
  Avoid storing food too close to walls. :contentReference[oaicite:23]{index=23}

Care & Cleaning

1. Clean interior surfaces with mild soap and warm water; avoid harsh abrasives.
2. Wipe exterior with soft cloth using non-abrasive stainless cleaner (for stainless finishes).
3. Replace water filter regularly (as indicated by filter change light).
4. Clean the condenser coils (if accessible) periodically to maintain efficiency.
5. Check and clear the defrost drain to prevent water pooling.
6. If not in use for extended periods, unplug and leave doors slightly open to prevent odor or mildew.

Troubleshooting

• Not cooling: Check power connection, temperature setting, ensure vents not blocked, clean coils.
  Condenser dirt or door ajar can impair cooling. :contentReference[oaicite:24]{index=24}
• Ice maker not working: Ensure water supply on, filter is installed, ice maker is turned on.
  Check for frozen lines or clogged filter. :contentReference[oaicite:25]{index=25}
• Water pooling inside: Drain tube may be clogged — check and clear.
  Ensure leveling so water flows to drain. :contentReference[oaicite:26]{index=26}
• Door doesn’t seal: Check gasket, alignment, and leveling.
  Adjust rollers or hinges as needed. :contentReference[oaicite:27]{index=27}
• Strange noises: Some fan, compressor hum, or refrigerant flow sounds are normal.
  If loud/unusual, check for obstruction, vibration, parts contact. :contentReference[oaicite:28]{index=28}
• Dispenser locked / not dispensing: Check lock setting, control panel settings, or filter blockage. :contentReference[oaicite:29]{index=29}

Installation Instructions

Warning: Disconnect power and water supply before installation. Follow local electrical and plumbing codes. Use a qualified technician if uncertain.

Unpacking & Positioning

• Carefully remove foam, tape, and packaging.
  Inspect for shipping damage before use. :contentReference[oaicite:30]{index=30}
• Leave clearance for ventilation (top, back, sides) as per manufacturer’s spec. :contentReference[oaicite:31]{index=31}
• Do not install near heat sources (stove, direct sunlight).
  Avoid placing where ambient temp < 55 °F (13 °C) or > 110 °F (43 °C). :contentReference[oaicite:32]{index=32}

Leveling & Door Adjustment

• Adjust front rollers / leveling legs so the cabinet is stable and slightly tilted back to keep doors closed.
  Use a wrench / socket to adjust. :contentReference[oaicite:33]{index=33}
• Check door alignment, ensure doors are flush and seals contact properly.
  Adjust hinges if needed. :contentReference[oaicite:34]{index=34}

Electrical & Water Connections

• Use a grounded 120 V AC dedicated circuit. Do not use extension cords.
  Power requirements as per manual. :contentReference[oaicite:35]{index=35}
• Connect water line with proper tubing (e.g., ¼" copper or approved synthetic).
  Flush line before installation. :contentReference[oaicite:36]{index=36}
• Install filter cartridge before using dispenser / ice maker.
  Follow orientation and priming instructions. :contentReference[oaicite:37]{index=37}

Door Removal / Reinstallation

• When needed for delivery or tight spaces, door(s) can be removed following factory instructions.
  Remove screws, lift off hinges carefully. :contentReference[oaicite:38]{index=38}
• Reinstall by reversing steps; confirm proper seating of gaskets, alignment, and operation.
  Test door closure and seal after reinstallation. :contentReference[oaicite:39]{index=39}