Frigidaire FFID2426TS4A Dishwasher Operation Manual

The Frigidaire FFID2426TS4A is a 24-inch built-in dishwasher with stainless steel finish, featuring OrbitClean® wash system, EvenDry™ drying technology, and a third rack for utensils. It offers 14 place settings capacity, ENERGY STAR® certification, and quiet 54 dBA operation. Ideal for modern kitchens, it's compatible with standard plumbing and electrical systems. Below are the key specifications and operation instructions. For local service or parts "near me," visit frigidaire.com/support to find authorized dealers using your ZIP code.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Dishwasher 2.3. Care and Cleaning 2.4. Troubleshooting 3. Installation Instructions 3.1. Remove Old Dishwasher 3.2. Installing New Dishwasher 3.3. Electrical Connections 3.4. Water Supply 3.5. Drain Connection

Key Specifications

Type: 24-inch built-in dishwasher with OrbitClean® and EvenDry™
Compatibility:
- Residential use; ENERGY STAR® and NSF certified
- Standard 120V, 60Hz household current
- Water pressure: 20-120 PSI
- Hot water supply at least 120°F (49°C)
- Compatible with food waste disposers (if empty)
Power Source:
- 120 V, 60 Hz; 15A circuit (dedicated)
- Grounded outlet required
Electrical Rating:
- 15A fuse or circuit breaker
- 2-wire with ground
Dimensions: 24" W x 25-3/4" D x 33-1/2" - 34-1/2" H (adjustable)
Features:
- Wash cycles: Normal, Heavy, Quick Wash, Rinse Only
- Options: Heat Dry, Hi-Temp Wash, Sanitize, Delay Start (2-4 hours)
- Capacity: 14 place settings + third rack for utensils
- BladeSpray® Arm and OrbitClean® for better coverage
- DishSense® Technology adjusts cycle time
- Stainless steel tub and filter; low rinse-aid indicator
- Quiet: 54 dBA; Annual Energy: 270 kWh
Operating Conditions:
- Water temperature: 120°F-140°F (49°C-60°C)
- Humidity: Non-condensing
Wash Cycle Details:
- Normal: ~2 hrs, ~5 gal
- Heavy: ~2.5 hrs, ~8 gal
- Quick: ~1 hr, ~4 gal
- Rinse Only: ~30 min, ~2 gal

Operation Instructions

Initial Setup

1. Load Dishes: Scrape large food particles; load upper/lower racks and third rack properly, avoiding nesting.
2. Add Detergent: Use automatic dispenser; fresh powder or gel, amount per soil level.
3. Add Rinse Aid: Fill dispenser (indicator light when low); adjust for spotting.
4. Run Hot Water: At sink until hot, then close.
5. Select Cycle: Use Ready-Select® controls; lights confirm.
6. First Use: Run empty Normal cycle with detergent.

Operating the Dishwasher

1. Select Cycle: Press for Normal, Heavy, Quick Wash, or Rinse Only.
2. Select Options: Heat Dry (for plastics), Hi-Temp Wash, Sanitize (NSF certified), Delay Start.
3. Control Lock: Hold Start for 3 seconds to lock controls.
4. Start: Close door firmly; press Start. Unit fills, washes, rinses, dries.
5. Interrupt Cycle: Open door (pauses); add items, close to resume.
6. Cancel: Hold Start for 3 seconds to drain and reset.
Note: DishSense® may shorten cycles; normal sounds include sprays and drains.

Care and Cleaning

1. Filter: Clean monthly; twist out lower filter, rinse under water.
2. Spray Arms: Remove and clear clogs with toothpick; check monthly.
3. Exterior/Interior: Wipe with soft cloth and mild soap; avoid abrasives.
4. Monthly Clean: 2 cups white vinegar in bottom rack, run Normal (no detergent).
5. Rinse Aid: Refill as needed; adjust dispenser setting 1-6.
Note: Use only dishwasher-safe items; separate glassware from knives.

Troubleshooting

Won't Start: Check power, door latch, cycle selected, no Delay Start.
No Water Fill: Water supply on? Inlet valve screen clean? Pressure 20+ PSI.
Poor Drainage: Hose kinked? Disposer empty? Clean filter and air gap.
Soils on Dishes: Pre-rinse heavy soils; use correct cycle/detergent; hot water.
Spotting/Filming: Hard water? Increase rinse aid; test hardness.
Not Drying: Select Heat Dry; unload promptly; plastics air dry.
Leaking: Level unit; check door seal; correct detergent amount.
Long Cycles: Normal with options; DishSense® adjusts.
Note: For "near me" service, use Frigidaire's locator tool. If persists, call 1-800-374-4432.

Installation Instructions

Warning: Disconnect power and water before installation. Follow local codes; improper setup may void warranty.

Remove Old Dishwasher

Shut off power at breaker and water supply.
Disconnect drain hose, water line, electrical.
Unfasten from cabinet/counter; slide out.
Cap lines to prevent drips.

Installing New Dishwasher

Cabinet Prep: 24" W x 24" D opening; utilities access.
Level Legs: Adjust to fit under counter (33-1/2" min height).
Door Springs: Adjust for balance.
Route Hoses/Wires: Through cabinet hole.
Slide In: Align, push fully; connect drain first.
Level: Front-to-back and side-to-side.
Secure: Screws to countertop/cabinet.
Connect Water/Drain/Electrical: See subsections.
Test: Check for leaks; run cycle.

Electrical Connections

120V/15A dedicated circuit; no extension cords.
Connect black to hot, white to neutral, green to ground.
Use junction box or cord (3-prong).
Secure with strain relief.

Water Supply

3/8" NPT copper tubing; shut-off valve.
Flush line; connect to inlet with ferrule/nut.
20-120 PSI; 120°F min temp.
Avoid kinks.

Drain Connection

High loop or air gap (required by code).
Connect to sink/disposer (remove plug).
Secure clamps; max length 10 ft, min height 32".
No sags in hose.